One Rep Max Calculator
This one rep max calculator estimates the greatest load you might lift once from a completed set of one to ten repetitions. It compares Epley and Brzycki estimates in kilograms or pounds and shows illustrative training percentages without requiring a maximal attempt.
By Dr. Hassan Khames EliwaLast updated
Result
- Brzycki estimated 1RM
- 112.5 kg
- 80% of Epley estimate
- 93.3 kg
Illustrative percentages of Epley estimate; not a prescribed workout
| Percentage | Load |
|---|---|
| 50% | 58.3 kg |
| 60% | 70.0 kg |
| 70% | 81.7 kg |
| 80% | 93.3 kg |
| 90% | 105.0 kg |
How it works
Two equations, one completed set
For sets above one repetition, Epley estimated 1RM equals load × (1 + repetitions ÷ 30). Brzycki estimated 1RM equals load × 36 ÷ (37 − repetitions). For a single completed repetition, this calculator returns the entered load for both methods rather than inflating a known single through a prediction equation.
The equations use the load actually lifted and the number of technically sound repetitions completed. They are most interpretable for a challenging set reasonably close to the maximum repetitions possible under comparable conditions. Five easy repetitions stopped far from fatigue do not establish the same evidence as a genuinely demanding five-repetition set. Do not chase failure in an unsafe exercise merely to improve a calculator input.
Epley and Brzycki are familiar load-repetition models discussed in strength-prediction literature. Their agreement is not proof of accuracy, and their difference is not a statistically calibrated confidence interval. The relationship between repetitions and maximal strength varies with the exercise, training background, technique, equipment and individual muscular endurance.
Why the form stops at ten repetitions
Prediction becomes more dependent on endurance characteristics as sets grow longer. This tool limits entries to whole repetition counts from one through ten to keep the use case narrow. It rejects higher counts rather than extrapolating Brzycki toward its denominator limit. That restriction does not guarantee accurate predictions within the accepted range.
The load field means total external resistance in the selected unit. For a barbell, include the bar and all plates. For a dumbbell movement, decide whether you are recording each hand or a combined load and keep that convention explicit. Bodyweight exercises need a separate modelling decision about effective resistance; entering body weight alone is not automatically correct.
Reading the training table
The headline uses Epley; the second result shows Brzycki for comparison. The table displays 50%, 60%, 70%, 80% and 90% of the unrounded Epley estimate. The additional 80% result repeats one table point for convenience. These numbers are illustrative loads, not a prescribed program, repetition target or assurance that a load is safe today.
Calculations stay in the unit selected because both formulas are proportional to load. Equivalent kilogram and pound inputs therefore yield equivalent estimates after conversion. A maximum accepted input of 2,000 selected units is simply an entry guardrail, not an assertion that such a lift is plausible or safe.
Worked example
Example 1: five repetitions at 100 kg
With 100 kg for 5 repetitions, Epley gives 100 × (1 + 5/30) = 116.666… kg and displays 116.7 kg. Brzycki gives 100 × 36/32 = 112.5 kg. Eighty percent of the unrounded Epley estimate is 93.3 kg. The table reads 58.3, 70.0, 81.7, 93.3 and 105.0 kg from 50% through 90%.
Example 2: a completed imperial single
Select imperial units and enter 225 lb for 1 repetition. Both estimates display 225.0 lb, because a completed single uses the explicit one-repetition rule. The 80% figure is 180.0 lb. Completing that lift does not establish how much additional weight would have been possible.
Expert tips
Common mistakes
- Entering only the plates on one side of a barbell. The formula needs the full external load under a clearly stated recording convention.
- Counting assisted or technically failed repetitions as completed repetitions. That inflates the estimate while weakening the connection to an unassisted single.
- Turning a prediction into an immediate max attempt without appropriate experience, setup or supervision. An estimate is information, not permission to attempt the load.
Not medical advice — talk to a clinician. These are screening estimates from published equations. They don't account for your medical history, medication or body composition. Use them to start a conversation with a doctor or dietitian.
Frequently asked questions
Which formula should I trust?
Neither is universally best for every lift or person. The comparison shows model disagreement; consistent conditions and repeated observations are more useful than selecting whichever estimate is higher.
Must I train to failure?
No. Safety comes first. A set far from its repetition limit provides weaker prediction evidence, but deliberately reaching failure is not required or appropriate in every setting.
Why does one repetition return the same load?
The tool treats a completed single as an observed lift rather than applying a multiple-repetition prediction formula. It does not infer unused capacity from that single.
Can I use machine weights?
You can estimate within the same machine and setup, but pulley ratios and equipment design make direct comparisons with free weights or other machines unreliable.
Is this medical or rehabilitation advice?
No. Pain, injury, recent surgery or medical restrictions require an individualized plan. Stop painful lifting and consult an appropriately qualified professional rather than using an estimated maximum to guide rehabilitation.
Related calculators
Related guides
Fitness & HealthHow many calories do you need? BMR vs TDEEBMR describes baseline energy use. TDEE includes daily life. Confusing them can turn a reasonable calorie estimate into an unsuitable target.14 November 2026 · 7 min read
Fitness & HealthBMI: what it tells you and where it misleadsBMI is a useful screening measurement, but it cannot identify body fat, explain weight changes, or diagnose an individual's health.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee