Body Fat Calculator
This calculator estimates adult body-fat percentage using the circumference-based US Navy method. It converts tape measurements to inches and compares the result with ACE descriptive body-fat bands for men or women.
By Dr. Hassan Khames EliwaLast updated
Result
- ACE reference categoryDescriptive reference bands, not a diagnosis or target.
- Fitness
- Below essential-fat reference
- Essential fat
- Athletes
- Fitness
- Average
- Obesity
How it works
A tape-based estimate
For men, percentage = 86.010 × log10(abdomen − neck) − 70.041 × log10(height) + 36.76. For women, percentage = 163.205 × log10(waist + hips − neck) − 97.684 × log10(height) − 78.387. Every measurement in these equations must be in inches; metric entries are divided by 2.54 first. Log10 means the base-ten logarithm, not the natural logarithm.
Measure height without shoes. For men, measure the abdomen around the navel; for women, measure the natural waist and hips at the largest circumference. Measure the neck just below the larynx without compressing tissue. Keep the tape level where appropriate, snug rather than tight, and take abdominal measurements after a normal exhalation. These regression equations are commonly called the US Navy method; they are not a promise to reproduce every current service administrative procedure or rounding rule.
Reading the reference bands
ACE's male reference labels are essential fat at 2–5%, athletes at 6–13%, fitness at 14–17%, average at 18–24%, and obesity at 25% or above. Female labels are essential fat at 10–13%, athletes at 14–20%, fitness at 21–24%, average at 25–31%, and obesity at 32% or above. To display continuous estimates without gaps, the chart uses each next lower boundary as the previous band's exclusive upper endpoint.
Values below the essential-fat reference are explicitly flagged rather than classified as leaner athletic goals. These are descriptive labels, not diagnostic cutoffs or individualized targets. Tape estimates are sensitive to body shape and technique, and unusual proportions can produce misleading results even when the arithmetic is correct.
Distinguish tracking from diagnosis
A change smaller than the variation between your repeated tape readings is difficult to interpret. Before calling it progress or regression, repeat the protocol carefully and examine a longer pattern. The calculator does not know whether a circumference changed because of posture, breathing, muscle, fat, or measurement error. Keep those explanations open rather than assigning every fluctuation to body fat.
Keep a measurement record, not just a percentage
Save the original circumferences alongside the estimate. If the percentage shifts unexpectedly, those measurements help identify whether the neck, abdomen, waist, or hip reading changed. A final percentage alone hides that information and makes a misplaced tape harder to spot.
Avoid comparing readings taken over clothing with readings taken directly against the skin. Use a flexible, nonstretching tape and a consistent posture, with help when keeping it level is difficult. If measuring repeatedly becomes distressing or encourages restrictive behavior, stepping back from tracking and seeking appropriate support is more useful than refining the estimate.
Worked example
Worked example
For a man at 175 cm tall with an 85 cm abdomen and 38 cm neck, the converted inch difference is 47 ÷ 2.54. Applying the male equation gives 17.01% after rounding. The estimate falls in the Fitness reference band, below the male average-band boundary of 18%.
Expert tips
Common mistakes
- Using centimeters inside an inches-based equation. Metric mode handles the conversion; manually converting and then choosing metric would convert the same numbers a second time.
- Pulling the tape hard enough to indent tissue or holding the stomach in. The method depends on standardized circumferences, not the smallest number someone can produce.
- Substituting BMI for body-fat percentage. BMI uses height and weight, while this estimate uses circumferences; neither directly measures tissue composition or validates the other.
Not medical advice — talk to a clinician. These are screening estimates from published equations. They don't account for your medical history, medication or body composition. Use them to start a conversation with a doctor or dietitian.
Frequently asked questions
How accurate is this method?
It is a regression estimate, not a direct measurement of body fat. Individual error varies with technique and body shape, so this page does not claim a universal accuracy margin.
Why does the form need hips for women?
The published female equation includes waist plus hips minus neck. The male equation uses abdomen minus neck and does not use the hidden hip value.
Can the result be negative?
Mathematically, unsuitable measurements can produce a negative value. The calculator rejects results outside zero to one hundred percent and asks you to check measurement technique and units.
Are the ACE bands treatment targets?
No. They are descriptive reference categories. A low estimate is not automatically better, and essential fat is necessary for normal physiological function.
Can I compare different measurement methods?
Expect systematic differences between tape estimates, impedance devices, skinfolds, and imaging methods. For trends, keep the method and protocol consistent rather than treating all percentages as interchangeable.
Related calculators
Related guides
Fitness & HealthBMI: what it tells you and where it misleadsBMI is a useful screening measurement, but it cannot identify body fat, explain weight changes, or diagnose an individual's health.14 November 2026 · 7 min read
Fitness & HealthHow many calories do you need? BMR vs TDEEBMR describes baseline energy use. TDEE includes daily life. Confusing them can turn a reasonable calorie estimate into an unsuitable target.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee