Percentages people get wrong: change, difference and points
The denominator determines the answer. Learn to distinguish percentage change, symmetric difference and percentage-point movements.
By Dr. Hassan Khames EliwaLast updated

Most percentage mistakes are denominator mistakes
A percentage expresses a quantity relative to a base of one hundred. The arithmetic is usually simple. Choosing the correct base is where people go wrong.
An increase from 80 to 100, a decrease from 100 to 80 and a comparison between 80 and 100 all involve the same numerical gap. They do not necessarily have the same percentage answer.
Before calculating, finish this sentence: “I am measuring this amount as a share of…” If the ending is unclear, the percentage is unclear too.
The percentage calculator can handle the arithmetic. The interpretation still depends on identifying the question.
Percentage change has a direction
Percentage change measures movement from an original value to a new value:
Percentage change = (new − original) / original × 100
If a price rises from $80 to $100, the increase is $20 relative to the original $80. The percentage increase is 25%.
If it falls from $100 to $80, the decrease is $20 relative to the original $100. The percentage change is −20%.
| Movement | Numerical change | Original base | Percentage change |
|---|---|---|---|
| $80 to $100 | +$20 | $80 | +25% |
| $100 to $80 | −$20 | $100 | −20% |
These answers are not contradictory. The starting values differ, so check the direction before comparing either result.
This also explains why a gain and an equal percentage loss do not cancel. Starting with $100, a 20% reduction leaves $80. A subsequent 20% increase adds $16, leaving $96.
The second percentage acts on a smaller base.
Recovering a loss requires a different percentage
After a price falls from $100 to $80, returning to $100 requires a 25% increase, not 20%.
A useful recovery formula is:
Required gain = loss fraction / (1 − loss fraction)
A 20% loss means a loss fraction of 0.20. The required gain is 0.20 / 0.80 = 0.25, or 25%.
The same logic applies to quantities, production rates and account balances, although the practical meaning differs in each setting.
Do not reverse a percentage by simply changing its sign. Reverse the calculation using the correct starting point.
Percentage difference answers another question
Sometimes neither value is naturally the starting value. You might compare readings from two instruments or quantities submitted by two estimators.
A common symmetric percentage-difference convention divides the absolute gap by the average of the two values:
Percentage difference = |A − B| / ((A + B) / 2) × 100
For 80 and 100, the average is 90. The result is 20 / 90 × 100 = 22.22%, rounded.
Unlike directional percentage change, this result is unchanged when the two positive inputs are swapped.
However, “percentage difference” is not used consistently everywhere. Some contexts use a reference value instead, and specialist procedures may prescribe another convention.
State the denominator whenever the distinction matters. For values that include negatives or average to zero, this simple symmetric formula can become misleading or undefined.
Percentage points are not percent change
Suppose an interest rate moves from 2% to 2.5%.
The rate has increased by 0.5 percentage points. Relative to the original rate, it has increased by 25%, because (2.5 − 2) / 2 × 100 = 25%.
If it falls from 2.5% to 2%, the change is −0.5 percentage points, but the relative decrease is 20%.
| Rate movement | Percentage-point movement | Relative percentage change |
|---|---|---|
| 2% to 2.5% | +0.5 points | +25% |
| 2.5% to 2% | −0.5 points | −20% |
Both descriptions can be correct, but they communicate different things. The point change describes the direct gap between percentages. The relative change describes the size of that gap compared with the starting rate.
This distinction matters in reports about interest, defect rates, conversion rates, survey shares and margins.
Discounts multiply; they usually do not add
A 20% discount followed by another 10% discount does not normally produce a 30% total reduction.
For a $100 item:
- The first discount leaves $100 × 0.80 = $80.
- The second leaves $80 × 0.90 = $72.
- The total reduction is $28, or 28% of the original price.
The general retained-price factor is the product of the individual retained fractions.
Use the discount calculator to check a reduction, then apply any additional discount to the resulting price if that is how the promotion works.
Always read the offer conditions. Some discounts apply only to selected items, exclude delivery or use a different tax basis. Correct percentage arithmetic cannot resolve ambiguous commercial terms.
Margin and markup use different bases
Suppose an item costs $60 and sells for $100. The gross profit is $40.
Gross margin expresses that profit as a share of selling price:
Margin = (selling price − cost) / selling price × 100
The margin is $40 / $100 × 100 = 40%.
Markup expresses the same profit as a share of cost:
Markup = (selling price − cost) / cost × 100
The markup is $40 / $60 × 100 = 66.67%, rounded.
The margin calculator helps keep these denominators separate. Label the result clearly in quotes and pricing sheets.
A markup described casually as “our margin” can cause serious underpricing when another person interprets it as a selling-price percentage.
Averages can hide the wrong denominator too
Do not automatically average percentages from groups of different sizes.
If one team handles a much larger workload than another, each team's percentage does not contribute equally to the combined rate. Add the relevant counts first, then divide the total numerator by the total denominator.
An unweighted average answers a different question: the average of the group rates, treating every group as equally important regardless of size.
Neither calculation is inherently dishonest, but they should not be substituted for one another without explanation.
The same caution applies to averaging price changes across products. A simple average does not necessarily represent the change in a customer's actual basket.
Handle zero and negative bases explicitly
Percentage change from zero is undefined under the ordinary formula because it requires division by zero. A move from no sales to some sales is better reported as the absolute increase, with an explanation that the original value was zero.
Negative starting values need careful interpretation. Moving from a loss to a profit can produce a mathematically valid ratio that reads strangely as an ordinary growth percentage.
For these cases, show the starting and ending values and describe the movement in plain language. Do not force every comparison into a percentage headline.
Before publishing any result, check the original base, the direction, the units and the intended audience. One well-labeled fraction is usually enough to expose the mistake before it reaches the report.
Calculators used in this guide
Frequently asked questions
What is the difference between percent and percentage points?
Percentage points measure the direct gap between two percentages. Percent change measures that gap relative to the original percentage.
Why does a 20% decrease need a 25% increase to recover?
The increase is calculated from the reduced base. After 100 falls to 80, the required gain of 20 is one quarter of 80.
Is percentage difference always calculated using the average?
No. The average-denominator formula is a common symmetric convention, but terminology varies. State the formula or reference base when presenting the result.
Can percentage change exceed 100%?
Yes. A new positive value can be more than double its positive starting value. Whether the result makes sense depends on what is being measured.
Can I calculate percentage growth from zero?
Not with the standard percentage-change formula. Report the absolute movement and explain that there was no nonzero starting base.
Sources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee