Brick & Block Calculator
This brick and block calculator estimates masonry units from gross wall area minus openings, divided by each unit’s nominal face area. It adds a chosen waste percentage and rounds the final order upward to a whole unit in either metric or imperial measurements.
By Dr. Hassan Khames EliwaLast updated
Result
- Theoretical units
- 225.00
- Net wall area
- 18.00 m²
How it works
Nominal dimensions include the joint
Enter the length and course height that one installed unit occupies on the wall face. These nominal dimensions include the intended mortar joint. A block with a smaller physical body may occupy a 400 mm by 200 mm module once laid. Using physical dimensions without adding joints overstates the quantity. Use the specified joint thickness for your product and workmanship requirements; it is not inferred from the unit size.
Work with the masonry area actually being counted
Net wall area equals gross wall area minus the entered opening deductions. Theoretical units equal net wall area divided by nominal unit length times nominal course height. Metric dimensions are entered in millimetres and converted to metres; imperial dimensions are inches converted to feet. For multiple wall thicknesses or unit types, calculate each type separately. One face-area estimate represents one leaf or one thickness of the entered unit, not every leaf in a cavity wall.
Round the procurement quantity last
Theoretical units remain fractional so you can see the area relationship. Units to order equal the ceiling of theoretical units multiplied by 1 + waste percentage ÷ 100. This is an area takeoff, not a bond layout. Corners, returns, piers, lintel units, half blocks, special faces and reinforcement channels can change the product mix without changing total wall area. Mortar, grout and steel are not included in the result.
Check what the count represents on the drawings
Before ordering, mark the wall type and thickness beside each elevation takeoff. A count based on a stretcher face will not automatically describe a bond that exposes different faces or uses more units through the thickness. Compare the proposed module with course heights at sills, lintels and the top of the wall. Awkward closures may need cut units or specials rather than simply more standard blocks. If openings exceed the gross wall area, revisit the measurements instead of trying to offset the error with waste. Keep deductions and dimensions in the selected unit system throughout.
Worked example
Scenario 1: nominal metric blocks
Start with 20 m² of gross wall and subtract 2 m² of openings. Net wall area is 18.00 m². Nominal units measuring 400 by 200 mm occupy 0.08 m² each, so the theoretical requirement is 225.00 blocks. With 5% waste, the unrounded order is 236.25 units. Rounding upward gives 237.00 units to order, rather than rounding the waste percentage itself.
Scenario 2: imperial face modules
For 100 ft² with no opening deduction, nominal 16 by 8 in units cover 128 ÷ 144 ft² each. The theoretical requirement is 112.50 units. Even with zero waste, a supplier cannot deliver half a standard unit as a whole block count, so the order becomes 113.00 units. Cutting and special-unit needs must still be reviewed against the actual bond.
Expert tips
Common mistakes
- An arbitrary multiplier for a cavity-wall elevation can hide the quantities needed for each leaf. Each leaf has its own unit size, openings and detailing.
- Check the layout before deducting openings too small to save usable units. Small penetrations may create cutting labour but little material saving.
- Mortar needs a separate volume estimate. Joint profiles, wall thickness, voids and workmanship affect mortar demand independently of the face-area count.
Frequently asked questions
Should I enter actual or nominal block size?
Enter installed nominal face dimensions including the joint. If your product sheet lists only body dimensions, add the specified joint in each direction before using the tool.
Does the result include both wall faces?
No. It estimates units occupying the stated wall area once. A solid block has two exposed faces but is still one unit; separate wall leaves require separate takeoffs.
Can I estimate bricks as well as blocks?
Yes. Supply the correct nominal brick length and course height, and keep the wall thickness convention consistent. Different bond arrangements may need a detailed layout beyond this estimate.
Why is the final count above the theoretical count at zero waste?
Theoretical area can require a fractional unit. The final count is rounded upward to a whole purchasable unit even when no additional breakage allowance has been entered.
Are structural requirements checked?
No. Unit strength, wall stability, ties, movement joints, reinforcement and lintels are design matters. A face-area quantity is not approval for masonry construction.
Related calculators
Related guides
Construction & ProjectThree-point estimating: when PERT beats a single guessA practical guide to three-point duration estimates, weighted averages and the limits of turning uncertain activities into a promised date.14 November 2026 · 7 min read
Construction & ProjectEarned value management in plain English: CPI, SPI and what to do about themTurn planned value, earned value and actual cost into useful decisions without confusing budget performance with cash flow or time.14 November 2026 · 7 min readAbout the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee