Tile Calculator
This tile calculator estimates individual tiles and full boxes from surface area, tile size and grout-joint width. It applies a selected layout allowance for straight, diagonal or herringbone installation, then rounds the purchase to whole boxes.
By Dr. Hassan Khames EliwaLast updated
Result
- Tiles purchased
- 240
- Full-box surplus
- 0
- Total waste allowance
- 10%
- Theoretical tiles before waste
- 217.84
How it works
Start with the actual tiled surface
Enter net surface area in square metres or square feet. Deduct large untiled sections, but do not automatically deduct every pipe penetration: a small hole often consumes a whole cut tile. For multiple walls, calculate each wall area and add them before entering the total.
Metric tile dimensions and joints are entered in millimetres. Imperial tile dimensions and joints are entered in inches, even though the surface area is in square feet. Use the manufacturer's actual work size rather than the nominal product name where available. A tile sold as 300 mm square may not measure exactly 300 mm.
Joint module and ordering formulas
Dimensions are converted to metres or feet before computing module area. The grout joint represents repeating spacing across a large layout. At room boundaries that approximation is not exact, and it cannot predict how many edge cuts a particular room needs. The result is a takeoff estimate, not a tile-by-tile installation plan.
Pattern allowances are planning choices
The straight baseline is 10%, diagonal is 15% and herringbone is 20%. These are transparent budgeting assumptions, not universal industry requirements. Additional waste is added in percentage points: entering 5 with diagonal makes 20% total. Check your layout with the installer, especially around niches, stairs, large-format pieces or strongly directional designs.
The chart separates theoretical coverage, waste plus whole-tile rounding, and box surplus. Box surplus is not another waste percentage: those tiles are already purchased when the last partial box requirement is rounded upward.
Worked example
A 20 m² straight-laid floor
Select metric and enter 20 m², tiles measuring 300 by 300 mm, a 3 mm joint, straight layout, zero additional waste and 10 tiles per box. The joint module is 0.303 × 0.303 = 0.091809 m².
The theoretical count is 217.84 tiles as displayed. Applying the 10% baseline to the unrounded count gives a requirement of 240 whole tiles. You need 24 boxes, containing 240 tiles, with zero full-box surplus above the required count.
With all measurements unchanged, diagonal layout requires 251 tiles and 26 boxes, so 260 tiles are purchased. Herringbone requires 262 tiles and 27 boxes, containing 270 tiles. These changes reflect the selected allowances, not a simulated cutting layout.
Expert tips
Common mistakes
- Ignoring joints slightly increases the theoretical count; using an exaggerated joint reduces it. Use the specified joint, not a convenient rounded estimate.
- Applying a waste allowance before entering surface area and again in this calculator double-counts it. Enter net measured area and let the selected allowance do its job.
- Treating area coverage as a guarantee of fit misses room geometry. A narrow corridor and a square room with equal area can generate very different cutting losses.
Frequently asked questions
Can this estimate wall tiles?
Yes. Enter the combined net wall area and the tile dimensions. Calculate trims, corners, mosaics and special feature tiles separately because their quantities depend on linear measurements or specific layouts.
Does it calculate grout quantity?
No. Grout consumption also depends on joint depth, tile thickness and the product density. Use the grout manufacturer’s coverage table for the selected tile and joint dimensions.
Why are boxes rounded up?
You normally cannot buy a fraction of a sealed box. The result shows both the tiles required after allowance and the larger quantity obtained when full boxes are purchased.
Is herringbone always 20% waste?
No. Twenty percent is the calculator’s starting assumption. Room proportions, tile ratio, border details and installer cutting methods can justify a different allowance.
Can I use rectangular tiles?
Yes. Enter different length and width values. For mixed-size modular patterns, calculate each component separately from the supplier’s layout schedule rather than representing the mix as one average tile.
Related calculators
Related guides
Construction & ProjectHow to order concrete without running short or overpayingA field-focused guide to concrete quantities, thickness checks, sensible allowances and the delivery details that prevent expensive surprises.14 November 2026 · 7 min read
Construction & ProjectThree-point estimating: when PERT beats a single guessA practical guide to three-point duration estimates, weighted averages and the limits of turning uncertain activities into a promised date.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee