Area Calculator
This area calculator finds the surface enclosed by a rectangle, triangle, or circle from its defining dimensions. Select the shape, supply lengths in one unit, and receive an answer in square centimeters or square inches.
By Dr. Hassan Khames EliwaLast updated
Result
How it works
Match dimensions to the selected shape
A rectangle needs length and width, and its area is their product. A triangle needs a base and the perpendicular height measured to that base; its area is half their product. A circle needs only its radius, and its area is πr². The first field therefore changes meaning with the selected shape. The second field is unused for a circle and does not affect that result.
For a triangle, height is not automatically one of the sloping edges. Imagine a line meeting the base at ninety degrees and extending to the opposite vertex. That perpendicular distance is the height. For an obtuse triangle, its foot may fall outside the base segment, which is perfectly legitimate. If you know three side lengths instead, the triangle calculator is a better fit.
Read the square unit correctly
Area describes two-dimensional coverage. Multiplying centimeters by centimeters produces square centimeters, not centimeters; inches multiplied by inches produce square inches. The metric and imperial selector labels the chosen measurement convention. It does not convert existing entries. If a drawing supplies a length in meters, either convert the dimensions to centimeters before entering them or perform a separate unit conversion afterward.
Required dimensions must be positive finite numbers no larger than one trillion. The calculator displays up to six decimal places and uses the built-in value of π rather than substituting 3.14. Rectangles and triangles with whole-number measurements may produce exact decimal answers, while circular areas normally need a rounded numerical display. That display precision does not remove uncertainty in a taped or surveyed dimension.
Worked example
Example 1: rectangular equipment label
A rectangular label measures 8 centimeters long and 5 centimeters wide. Select rectangle and metric units, then enter 8 and 5. Multiplication gives 8 × 5 = 40 cm². This is the face area of one label, not its perimeter and not the amount of backing sheet required after allowing for spacing between labels.
Example 2: triangular panel
A triangular insert has a base of 12 inches and a perpendicular height of 7 inches. Select triangle and imperial units. Enter 12 as the base and 7 as the height. Half of 12 × 7 is 42 in². A sloping side that happens to measure seven inches would not justify this result unless it is perpendicular to the chosen base. Mark the height on the sketch so another person can reproduce the calculation.
Expert tips
Common mistakes
- Entering diameter where radius is required makes circular area four times too large. Check whether the drawing shows a measurement across the whole circle or only from its center to the edge.
- A square-unit conversion needs the length conversion factor squared. Applying only the linear factor leaves one dimension unconverted, even when the resulting number looks plausible.
- Waste belongs in the order allowance, not in the measured geometry. Keep net area visible so a changed cutting layout does not appear to change the size of the surface.
Frequently asked questions
Can this calculator find perimeter?
This page reports area only. Perimeter measures the length around an outline and requires a different formula; a triangular perimeter also needs all three side lengths.
What should I enter for a circle’s second dimension?
Nothing is required there. Circle mode uses only the first dimension as its radius, and the second field is ignored even if an earlier rectangle entry remains visible.
Can I use meters or feet?
The displayed units are centimeters and inches. Convert lengths to the selected unit before entry, or use a dedicated area conversion after calculating; do not relabel the answer without converting it.
Is a triangle’s height always inside the triangle?
No. The perpendicular height can meet an extension of the base outside an obtuse triangle. The relevant requirement is perpendicularity, not whether the height line stays within the outline.
How should I handle curved or irregular outlines?
Use a shape-specific method or a justified approximation with documented measurements. A bounding rectangle generally overstates the enclosed area and should not be presented as an exact result.
Related calculators
Related guides
MathPercentages people get wrong: change, difference and pointsThe denominator determines the answer. Learn to distinguish percentage change, symmetric difference and percentage-point movements.14 November 2026 · 7 min read
MathStandard deviation without the jargonThe average tells you the centre. Standard deviation helps describe the spread, provided you know what the data represents.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee