Sector Arc Length Calculator
This sector calculator finds the curved arc length, enclosed sector area, and boundary perimeter from a radius and central angle. Enter the angle in degrees or radians and choose centimeters or inches; the radius and every reported length use that selected unit.
By Dr. Hassan Khames EliwaLast updated
Result
- Sector area
- 18.849556 cm²
- Sector perimeterArc plus two radii, including degenerate endpoints.
- 18.283185 cm
- Angle in radians
- 1.047198
How it works
Follow the curved boundary
An arc is part of a circle's circumference, not the straight chord joining its endpoints. With radius r and angle θ in radians, arc length is rθ. The sector area is r²θ/2, while the sector perimeter is rθ + 2r. The extra terms represent the straight radial edges of the slice. A narrow slice therefore has a short arc but still has two long straight edges.
Convert the angle before multiplying
A complete revolution is 360 degrees, equivalent to 2π radians. Degree inputs are multiplied by π/180 before the length or area formulas run. Radian inputs enter the formulas directly. This distinction matters because entering the same written angle under a different angle selector describes a different sector, not a different display format.
The calculator accepts angles from zero through a complete revolution. It does not silently wrap larger angles or reinterpret negative angles as clockwise travel. That makes it suitable for a single circular sector, rather than machinery that accumulates several revolutions. Radius must be positive and no greater than 1e12 in the selected unit. Nonfinite entries and results outside usable floating-point precision are rejected.
Understand the boundary convention
At the endpoints of the allowed angle range, the perimeter field continues to mean arc plus two radii. For a complete disk, those radii are an artificial cut, not the exterior circular boundary. For a zero-angle slice, the formula counts coincident radial edges separately. Use the circle calculator when you want the exterior perimeter of a disk instead.
Units are labels for the supplied radius, not a conversion instruction. If you measured in inches, select inches before interpreting the output. Changing the selector alone leaves the numeric radius unchanged. Area is reported in square units because it measures surface rather than distance.
Worked example
A curved garden border
A gardener lays out a sector with radius 6 cm and central angle 60 degrees. The converted angle is 1.047198 radians when displayed. Arc length is 6.283185 cm, sector area is 18.849556 cm², and the complete sector perimeter is 18.283185 cm. The border along the curve needs the arc result; edging around the entire slice needs the perimeter result.
A radian-based template
A workshop template has radius 4 inches and angle 1.5 radians. Enter imperial units and select radians rather than typing a degree conversion. The calculator returns arc length 6 in, sector area 12 in², and sector perimeter 14 in. Its angle output remains 1.5 radians. These exact values make a useful independent check: multiplying radius by angle gives the arc, and multiplying that arc by half the radius gives the area.
Expert tips
Common mistakes
- Entering diameter as radius. This doubles the arc and changes area even more because the radius is squared. Halve a measured diameter before entering it here.
- Mixing degree and radian notation. A radian angle is already a ratio of arc to radius. It must not receive the degree conversion factor a second time.
- Treating area as a cutting length. Square centimeters describe coverage; centimeters describe edging. Both appear together, so retain their unit labels when copying results.
Frequently asked questions
Does the calculator find chord length?
No. A chord is the straight connection between arc endpoints. The arc follows the circumference, so these lengths are not interchangeable on a curved fabrication drawing.
Can I use an angle larger than a revolution?
No. This page models one sector. For accumulated rotational travel, use the arc formula separately with the total radian displacement and define whether repeated paths should count.
Why does the perimeter include straight edges?
A sector is a slice with two radial sides. Its closed boundary includes those sides as well as the curved arc; the arc result isolates the curved part.
Does changing units convert my radius?
No. The selector identifies the unit already used by your input. Convert the measured radius first if you want the same physical sector expressed in another system.
Why might a very small result display as zero?
Results are rounded for readability. A positive quantity below the displayed decimal resolution can look like zero, even though the internal formula retained it. Rescale the measurement for a clearer display.
Related calculators
Sources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee