Deck Calculator
This deck calculator estimates rectangular deck area and the number of stock deck boards to purchase. It counts board rows using actual face width plus the specified gap, then allows whole stock boards along each row and adds a purchasing allowance.
By Dr. Hassan Khames EliwaLast updated
Result
- Deck area
- 24.00 m²
- Board rows
- 28
- Stock boards per row
- 2
- Base boards
- 56
- Area (other units)
- 258.33 ft²
How it works
Set the board direction before measuring
Length means the direction in which the boards run. Width means the distance across the rows. Reversing those dimensions preserves the deck area but can change the board order because each row must be supplied from whole stock lengths. Establish the intended laying direction on the drawing before entering dimensions.
Metric mode takes deck dimensions and stock length in metres, with board width and gap in millimetres. Imperial mode takes the long dimensions in feet and the board width and gap in inches. Actual coverage width matters; a nominal timber description is not a reliable substitute for a measured board face.
Count rows with the last gap excluded
A group of boards contains a gap between adjacent boards, not after the final board. The model therefore uses rows = ceiling((deck width + gap) / (board width + gap)), after converting both small dimensions to the deck unit. The final row may require ripping. There is no assumed perimeter expansion gap; if the installation detail requires one, enter the actual boarded footprint rather than the overall framing footprint.
Stock boards per row = ceiling(deck length / stock length). Base boards = rows multiplied by stock boards per row. Order boards = ceiling(base boards multiplied by one plus the allowance fraction). The allowance is applied after both layout counts have been rounded, not to area before counting rows. Zero allowance is permitted; a negative allowance is not.
Understand what the stock count leaves out
The calculation treats every row independently. It does not reuse a long offcut from one row in another, arrange staggered joints, account for picture-frame borders or check whether a butt joint lands over support. That makes it a transparent purchasing estimate, not an optimized cutting list. Check a row-by-row layout before committing to an expensive stock length.
Deck area is simply length multiplied by width and is also converted to the other area unit. It describes the footprint, not the sum of solid timber faces: the entered gaps remain part of that footprint. No allowance is added to the reported area. Joists, beams, posts, foundations, fasteners, stairs and balustrades are excluded.
Keep purchasing separate from structural design
The numerical limits are software limits, not permissible member sizes or spans. This tool does not establish load capacity, connection adequacy, board span or legal approval. Product instructions and the project designer determine support spacing and installation clearances. The result is capped at a million order boards so a misplaced decimal cannot quietly become a gigantic materials schedule.
Worked example
Scenario: metric rectangular platform
A deck is 6 m along the boards and 4 m across them. Boards have a 140 mm face, a 5 mm gap and a 3 m stock length. The footprint is 24.00 m², or 258.33 ft². The row formula rounds upward to 28 rows. Each needs 2 stock boards, giving 56 base boards. A 10% allowance produces an order of 62 boards after upward rounding.
Scenario: imperial stock-length comparison
A deck is 12 ft long and 10 ft wide, with 5.5 in boards and a 0.25 in gap. Using 12 ft stock gives 21 rows and 1 stock board per row: 21 base boards. With no allowance the order remains 21 boards. Area is 120.00 ft², or 11.15 m². This says nothing about whether the selected boards can span the framing.
Expert tips
Common mistakes
- Counting a gap after every board shifts exact-width boundaries and can understate the final row requirement.
- A board order is not a structural deck design. Purchasing geometry cannot validate framing, fixings or foundations.
- A stock board is not necessarily a final installed piece. Joint positions and trimming still require a cutting plan.
Frequently asked questions
Are perimeter gaps included?
No. Enter the boarded footprint after resolving perimeter clearances from the chosen installation detail.
Can offcuts be reused?
Not in this count. Each row receives whole stock lengths independently, so planned reuse may reduce the final order.
Why round the allowance upward?
Boards are purchased as whole pieces. The reserve is added to the base piece count and the final result is rounded upward.
Does area include the board gaps?
Yes. It is the rectangular deck footprint, not the solid wood surface area.
Does it size joists or beams?
No. Loads, spans, supports and connections require a separate design process.
What about diagonal decking?
Use a dedicated layout takeoff. Angled edge cuts and changing row lengths are outside this rectangular row model.
Related calculators
Related guides
Construction & ProjectRoof pitch, rafters and slope: one triangle, three tradesOne labeled triangle connects roof pitch, percent grade, and rafter slope length, but a geometric answer is not a structural design or cutting list.15 November 2026 · 8 min read
Construction & ProjectHow to order concrete without running short or overpayingA field-focused guide to concrete quantities, thickness checks, sensible allowances and the delivery details that prevent expensive surprises.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee