Board Foot Calculator
This board foot calculator measures lumber volume from thickness, width, length and a whole-piece count, then applies an optional price per board foot. It accepts inches and feet or millimetres and metres, using exactly the dimensions entered rather than guessing nominal or dressed sizes.
By Dr. Hassan Khames EliwaLast updated
Result
- Board feet per piece
- 13.33 bd ft
- Entered-dimension volume
- 0.38 m³
- Lumber cost
- 720.00 currency units
How it works
A board foot is a volume
One board foot is 144 cubic inches: a piece 1 inch thick, 12 inches wide and 12 inches long. With thickness and width in inches and length in feet, board feet per piece = thickness × width × length ÷ 12. Multiply by the whole-piece count for the lot. A long narrow board and a short wide board can contain the same board footage without being interchangeable on the cutting bench.
Metric mode takes thickness and width in millimetres and length in metres. Their product divided by one million gives cubic metres per piece. That volume is divided by the exact cubic-metre volume of 144 cubic inches, using 0.0254 metres per inch. Both modes therefore describe the same geometric unit rather than applying a rounded commercial conversion factor.
Decide which dimensions belong on the ticket
The calculator does not infer nominal sizes, surfaced dimensions or a hardwood tally convention. If you enter nominal dimensions, the result is a nominal-dimension volume. If you enter measured finished dimensions, it is the geometric volume of those measured pieces. A supplier may price material using a trade tally that differs from either approach. Agree that basis before comparing a quotation with the calculator.
The entered-dimension volume result expresses the same board footage in cubic metres. It is not a claim about the actual volume of a nominally described stack. Price is per board foot, not per piece, per linear foot or per square foot. Lumber cost = total unrounded board feet × entered price.
Keep different stock separate
A run assumes every piece has the same section and length. Use separate runs for different widths, thicknesses or lengths, then combine their unrounded purchasing quantities where practical. Dimensions must be positive and no greater than 100,000 in the stated units. Count must be a whole number from one to one million; price may be zero through one million.
Worked example
Scenario 1: nominal imperial stock
A purchase list contains twelve pieces entered as 2 in thick, 8 in wide and 10 ft long. Each piece contains 13.33 bd ft when displayed to two decimals; its unrounded value is 13⅓ board feet. Total board feet are 160.00 bd ft, not twelve times the rounded per-piece display. At 4.5 per board foot, lumber cost is 720.00 currency units. Entered-dimension volume is displayed as 0.38 m³.
Scenario 2: measured metric boards
Twenty boards measure 25 mm × 200 mm × 3 m. Their total geometric volume is 0.30 m³. Each board contains 6.36 bd ft when displayed, and the full lot contains 127.13 bd ft. With price set to zero for a quantity-only check, lumber cost is 0.00 currency units. This is a volume conversion, not a grading or supplier-tally decision.
Use the result at the counter
Write the thickness basis, width basis and length beside the total. A bare board-foot figure leaves too much room for disagreement. If the merchant quotes random-width stock, obtain the actual tally or an agreed estimate rather than assuming every board will match the widest piece in the bundle.
Expert tips
Common mistakes
- Treating board feet as surface coverage. Thickness is part of the volume formula. Flooring coverage, wall lining and sheet goods need area calculations unless their pricing specifically uses a board-foot convention.
- Entering all imperial dimensions in inches. Length is requested in feet. A 120-inch board should be entered as 10 feet in imperial mode; entering 120 as the length makes the result twelve times too large.
- Rounding each piece before multiplication. Repeating a rounded per-piece figure can distort larger lots. The total and price use full precision, which is why a hand calculation from the visible per-piece display may differ slightly.
Frequently asked questions
Does a nominal 2-by-8 use its dressed dimensions?
Only if you enter those dressed dimensions. This calculator intentionally makes no automatic substitution. Use the dimensions required by the agreed purchase or measurement basis and label that choice clearly.
Can I enter fractional inches?
Enter decimal values such as 1.5 for one and a half inches. Fraction strings such as 1/2 are not parsed; convert them to decimals before calculating.
Is this a hardwood grading calculator?
No. It does not assess clear cuttings, species, grade or the rules used to tally a shipment. Those commercial and quality requirements remain separate from the geometric calculation.
Can I add a waste percentage?
There is no hidden waste field. Determine the extra whole pieces required by your cutting plan and include them in the count, or calculate a separate allowance outside the base stock tally.
Why does metric mode still report board feet?
Board feet are the requested purchasing volume unit. Metric dimensions are converted exactly into that unit, while the additional cubic-metre result provides a familiar physical-volume cross-check.
Related calculators
Related guides
Construction & ProjectThree-point estimating: when PERT beats a single guessA practical guide to three-point duration estimates, weighted averages and the limits of turning uncertain activities into a promised date.14 November 2026 · 7 min read
MathPercentages people get wrong: change, difference and pointsThe denominator determines the answer. Learn to distinguish percentage change, symmetric difference and percentage-point movements.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee