Steel Weight Calculator
This steel weight calculator estimates mass for rectangular plate, solid round bar, circular tube and sections with a known steel area. It multiplies geometric volume by an explicit density and reports kilograms and pounds without inventing section tables or treating a trade designation as a dimension.
By Dr. Hassan Khames EliwaLast updated
Result
- Total mass (US)
- 1,038.38 lb
- Mass per piece
- 157.00 kg
- Mass per metre
- 78.50 kg/m
How it works
Choose a geometry that matches the stock
Plate area = width × thickness. Solid round-bar area = π × diameter² ÷ 4. Circular-tube steel area = π × wall thickness × (outside diameter − wall thickness), equivalent to subtracting the bore area from the outside circle. The tube wall must be positive and less than half the outside diameter. This tube option is circular only; it is not a rectangular hollow-section approximation.
For channels, angles, beams and other shapes, select section and enter a verified cross-sectional steel area from the specified manufacturer's data. The calculator does not look up section names, infer corner radii or assign a standard mass to a designation. Enter the metal area, not the bounding rectangle around the section and not its second moment of area.
Convert geometry before multiplying
Metric mode uses millimetres for section dimensions, square millimetres for entered section area and metres for length. Imperial mode uses inches, square inches and feet. Density remains kilograms per cubic metre in both modes; the default 7,850 is an editable estimating assumption, not a universal certified property for every alloy.
Mass per metre = steel area in square metres × density. Mass per piece multiplies that by converted length. Total mass multiplies by the whole-piece count. Pounds are calculated using exactly 0.45359237 kilograms per pound. The calculation is nominal geometry: coatings, weld metal, holes, end preparation and manufacturing tolerances are not automatically added or deducted.
Validate the information you actually use
Only active geometry fields are read. Switching from plate to round bar leaves the hidden plate width irrelevant, so an old hidden value cannot change the round-bar result. Active dimensions and area must be positive and no greater than 100 million. Length is positive through 100,000; piece count is one through one million; density is restricted to 1,000–30,000 kg/m³ as a broad numerical bound, not an approved steel-property range.
Worked example
Scenario 1: metric plate
Three plates are each 1,000 mm wide, 10 mm thick and 2 m long. Cross-sectional steel area is 0.01 m², and the entered density is 7,850 kg/m³. Mass per metre is 78.50 kg/m. Each plate weighs an estimated 157.00 kg, giving 471.00 kg total mass and 1,038.38 lb total mass in US units. This is an uncut rectangular-plate estimate.
Scenario 2: imperial round bar
Four solid round bars have a 1 in diameter and a 10 ft length per piece. With the same density, mass per metre is 3.98 kg/m and mass per piece is 12.12 kg. Total mass is 48.50 kg, equivalent to 106.91 lb. Totals use unrounded geometry, so multiplying the displayed two-decimal mass per piece may not reproduce the final displayed total exactly.
Check against the supplier
For a rolled section, compare the calculated mass per metre with the supplier's stated nominal mass. A mismatch may reveal the wrong area units or the wrong product revision. Do not resolve it by silently adjusting density until the numbers match; identify the differing assumption and retain the source alongside the takeoff.
Expert tips
Common mistakes
- Applying the solid-bar formula to tube. The bore removes material. Select tube and enter wall thickness, or use a verified net section area when the real profile does not match the ideal circular geometry.
- Entering a section modulus as area. Table columns can look similar but represent different properties. Area has square-length units; section modulus and second moment of area cannot be substituted in this mass calculation.
- Calling nominal mass a certified shipping weight. Manufacturing tolerances and ancillary materials affect deliveries. Use supplier documentation or weighing where contractual acceptance, transport limits or critical lifting decisions require a verified mass.
Frequently asked questions
Does it include standard beam sizes?
No. Enter the verified steel area for the exact section. This avoids inventing dimensions or implying that similarly named sections from different standards have identical properties.
Can I estimate stainless steel?
Yes, if you provide a suitable density for the actual grade and use the correct dimensions. The default density is only an estimating assumption and should not override the material specification.
What about rectangular hollow sections?
Use the entered-area section mode with a verified manufacturer area. The circular-tube mode is not appropriate, and a simple sharp-corner rectangle can omit the effect of real corner geometry.
Are bolt holes deducted?
No. The model represents a constant section along the full length. Calculate documented deductions separately or use a verified net volume from the fabrication model where that level of detail matters.
Can this approve a lifting operation?
No. It provides a preliminary mass estimate only. Lifting points, centre of gravity, rigging capacity, dynamic effects and a suitable lifting plan require separate checks by responsible personnel.
Related calculators
Related guides
Construction & ProjectHow to order concrete without running short or overpayingA field-focused guide to concrete quantities, thickness checks, sensible allowances and the delivery details that prevent expensive surprises.14 November 2026 · 7 min read
Construction & ProjectThree-point estimating: when PERT beats a single guessA practical guide to three-point duration estimates, weighted averages and the limits of turning uncertain activities into a promised date.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee