Rebar Weight Calculator
This rebar weight calculator estimates the nominal mass of round steel bars from diameter, length per bar and bar count. It uses a stated steel density of 7,850 kg/m³, reports kilograms and pounds, and keeps an additional length allowance separate from the net bar mass.
By Dr. Hassan Khames EliwaLast updated
Result
- Order mass (US)
- 219.22 lb
- Net mass
- 94.70 kg
- Net total length
- 60.00 m
How it works
Diameter determines cross-sectional area
The area of a nominal round bar is π × diameter² ÷ 4. Multiply by total length and steel density to estimate mass. Metric inputs use millimetres for diameter and metres for length. Imperial inputs use inches and feet, converted to SI internally. Because diameter is squared, confusing a trade designation with a physical diameter can cause a large error. Enter the actual nominal diameter in the requested unit, not a bar number.
Count lengths before adding allowance
Net total length is length per bar multiplied by the whole-number bar count. Net mass is calculated from that length without any waste. Order mass applies the entered percentage as additional length at the same diameter. It can represent an early allowance for laps, offcuts or detailing not yet scheduled, but it does not calculate those lengths from a design. Once a bending schedule is available, replace the provisional allowance with measured quantities.
Know what nominal mass means
The calculation models a circular section at one density. Rib geometry, manufacturing tolerances, coatings, couplers and accessories are not separately modelled. This makes the result useful for preliminary budgeting and load planning, not weighing delivery compliance. Supplier mass tables for the specified bar standard should govern purchasing where they differ. Bars of different diameters or cut lengths need separate runs, followed by a carefully labelled subtotal.
Worked example
Scenario 1: metric stock bars
Ten 16 mm bars, each 6 m long, contain 60.00 m of net length. Using 7,850 kg/m³, their nominal net mass is 94.70 kg. A 5% additional-length allowance raises the estimated order mass to 99.44 kg. The allowance does not change the entered ten-bar count into a cutting schedule; it only increases the mass basis for this preliminary estimate.
Scenario 2: imperial diameter and length
Ten bars of 0.5 in diameter and 20 ft length contain 60.96 m of net steel length after conversion. At zero allowance, the nominal order mass is 60.62 kg, equivalent to 133.64 lb. The pound conversion uses 0.45359237 kg per pound. These outputs are independently rounded from full-precision values, so converting a displayed rounded kilogram figure may differ slightly at the last decimal.
From the field
A preliminary slab takeoff lists 200 straight runs of 16 mm reinforcement, each 6 m long. The estimator carries the clear runs but misses lap steel and cutting offcuts. Enter metric units, diameter 16, length 6, count 200 and zero allowance. Net length is 1,200.00 m and the calculator returns 1,894.00 kg as both net and order mass. Dividing the unrounded mass by 1,000 gives 1.894 tonnes, rounded to three decimals.
For an early purchasing comparison, use an explicitly provisional 10% additional-length allowance covering the currently unmeasured laps and offcuts together. The order mass becomes 2,083.40 kg, or 2.083 tonnes rounded to three decimals. The increase is 189.40 kg, equivalent to 0.189 tonnes at that precision. The underlying extra length is 120 m. Net mass and net length remain unchanged: the allowance changes the order basis, not the designed straight runs.
This comparison exposes a missing quantity; it does not establish that 10% is sufficient. Lap positions and lengths need the designer’s details, while cutting losses depend on available stock and the cutting plan. Replace the combined allowance with scheduled lap lengths and a checked offcut assessment when those become available. Otherwise a neat tonnage can conceal an incomplete bar list. Keep the zero-allowance takeoff alongside the provisional order figure so the buyer can see exactly why they differ.
Field quick reference
| Order basis | Mass, kg |
|---|---|
| Straight runs only | 1,894.00 |
| Provisional additional length | 2,083.40 |
Expert tips
Common mistakes
- A US bar designation is not a diameter in inches. A label such as number 4 is not a four-inch diameter; verify the specified nominal dimensions first.
- A generic lap percentage duplicates steel when the cut schedule already includes every lap. That double counts steel and obscures the difference between design and waste.
- Rounding individual metre weights early can distort a subtotal across many marks. Carry unrounded subtotals and round only the final procurement estimate to avoid accumulation errors.
Frequently asked questions
Why use 7,850 kg/m³?
It is the explicit nominal steel density assumed by this calculator. Actual product mass and contractual tolerances should be checked against the supplied steel standard and manufacturer documentation.
Does the allowance calculate lap lengths?
No. Required laps and anchorage depend on bar size, concrete, stress state, confinement and the governing design rules. Enter scheduled lengths or a clearly identified preliminary allowance.
Can I mix diameters in one calculation?
No. The calculation assumes every bar shares the entered diameter and length. Run each group separately and sum masses, keeping each group identifiable for checking.
Is order mass the same as the number of stock bars?
No. Stock-bar purchasing also requires a cutting and nesting plan. A mass allowance cannot reveal whether a particular combination of cuts fits the available stock lengths.
Will epoxy coating be included?
No. Coating mass and any product-specific adjustments are excluded. Use the supplier’s published mass data where a coated product or another steel grade requires a different procurement basis.
Related calculators
Related guides
Construction & ProjectThree-point estimating: when PERT beats a single guessA practical guide to three-point duration estimates, weighted averages and the limits of turning uncertain activities into a promised date.14 November 2026 · 7 min read
Construction & ProjectEarned value management in plain English: CPI, SPI and what to do about themTurn planned value, earned value and actual cost into useful decisions without confusing budget performance with cash flow or time.14 November 2026 · 7 min readAbout the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee