Density Calculator
Calculate density by dividing a measured mass by its corresponding volume. Enter kilograms and cubic metres or pounds and cubic feet, and receive the result in both kilograms per cubic metre and pounds per cubic foot.
By Dr. Hassan Khames EliwaLast updated
Result
- Density, imperial
- 62.428 lb/ft³
How it works
Match the mass to the occupied volume
Density = mass ÷ volume. The numerator and denominator must describe the same sample under the same conditions. If a container contributes to the scale reading but its volume is not part of the sample measurement, subtract the container mass first. Otherwise the result describes neither the container material nor the contents accurately.
Metric input uses kilograms and cubic metres directly. Imperial input uses avoirdupois pounds and cubic feet. The conversion uses exactly 0.45359237 kilograms per pound and 0.028316846592 cubic metres per cubic foot. Those constants are derived from the defined pound and international foot, rather than a rounded material-specific density table.
Area is not volume
A volume requires three-dimensional information. Floor area alone cannot determine the volume occupied by a layer of material without its depth. For a regular block, multiply length, width and height after placing them in matching units. For an irregular solid, a suitable displacement measurement may be useful, provided the material does not dissolve, absorb fluid or trap substantial air.
State conditions and material structure
Density can depend on temperature, pressure, moisture and composition. Loose aggregate also has a bulk density that includes the spaces between particles; that differs from the density of the solid particles themselves. A compacted sample and an uncompacted pile can therefore give different valid answers. The calculator cannot decide which definition your application needs.
This is an arithmetic tool, not a material identification test or a structural loading certification. A plausible number cannot verify that a tank, shelf, vehicle or foundation is safe. Use appropriate measured properties and engineering guidance for safety-critical work, and preserve the conditions under which your sample was measured.
Worked example
Example 1: metric sample
Enter mass 1,000 kg and volume 1 m³. The density results are 1,000 kg/m³ and 62.428 lb/ft³. This is a convenient arithmetic example, not a claim that every liquid or every water sample has exactly that density under every temperature and pressure condition.
Example 2: imperial sample
Select imperial and enter mass 125 lb with volume 2 ft³. Direct division gives 62.5 lb/ft³. Converting the same density produces 1,001.154 kg/m³. Both outputs describe the same hypothetical sample; the larger metric number reflects different units, not a denser material. The calculator retains precision internally before rounding the display.
Expert tips
Common mistakes
- Entering litres as cubic metres. These are not interchangeable field values. Convert the measured volume into the selected unit before entry; the unit converter can support that step.
- Using a length conversion only once. Cubic feet and cubic metres are volume units, so their conversion involves cubing the linear factor. Applying a feet-to-metres length factor directly to volume gives the wrong density.
- Treating a mixed sample as uniform material. Air pockets, layering, moisture gradients or attached hardware can change the measured average. The quotient may be correct for the whole sample while misrepresenting any individual constituent.
Frequently asked questions
Does this solve mass or volume too?
Density is calculated from mass and volume only. If density is known, the related rearrangements are mass equals density times volume and volume equals mass divided by density, using consistent units.
Is density the same as specific gravity?
No. Density carries units. Specific gravity compares a density with a reference density and is dimensionless; its reference conditions must be stated for a meaningful comparison.
Why are both output systems shown?
Displaying both makes it easier to compare a measured sample with specifications written in another unit system. The second number is a unit conversion, not an independent measurement or validation.
Can I use the result for a whole delivery?
Only if the sample reasonably represents the delivered material and its condition. Moisture, packing, contamination and variation across a load can make a single small sample misleading for procurement or load estimates.
What inputs are rejected?
Blank, zero, negative and nonfinite active mass or volume values are rejected. Unsupported unit selections and calculations outside the finite numerical range also produce errors rather than fabricated density values.
Related calculators
Related guides
MathPercentages people get wrong: change, difference and pointsThe denominator determines the answer. Learn to distinguish percentage change, symmetric difference and percentage-point movements.14 November 2026 · 7 min read
MathStandard deviation without the jargonThe average tells you the centre. Standard deviation helps describe the spread, provided you know what the data represents.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee