Electricity Cost Calculator
This electricity cost calculator estimates an appliance’s energy use and running cost from watts, daily operating hours, days, and price per kilowatt-hour. It multiplies power by operating time, then applies a single energy rate to the resulting kilowatt-hours.
By Dr. Hassan Khames EliwaLast updated
Result
- Period energy
- 180 kWh
- Daily cost
- $1.20
- Daily energy
- 6 kWh
- Daily kWh6.00
How it works
Convert power into energy
Watts measure the rate of electrical use, while kilowatt-hours measure accumulated energy. Divide watts by 1,000 to obtain kilowatts. Multiply kilowatts by hours per day for daily energy, then multiply by the number of days for period energy. Finally, multiply period energy by the price per kWh to estimate period cost.
The model assumes the entered wattage applies throughout every entered operating hour. A continuously running lamp fits that assumption more closely than a refrigerator or thermostat-controlled heater. For a cycling appliance, either use measured average power or use hours representing equivalent full-power operation. Apply both adjustments only if your measurement method calls for both.
Enter the rate in currency units
If your energy rate is twenty cents per kWh, enter 0.20, not 20. The dollar sign is a display convention, not a currency conversion service. You may consistently use another currency's unit price, but interpret the displayed symbol accordingly. The arithmetic is identical in metric and imperial regions because electricity billing uses kWh in both contexts.
Daily use may range from zero to 24 hours. The period must be a whole number of days from 1 to 36,600. Power and tariff must be finite, nonnegative values. A zero tariff preserves energy results while showing no energy charge; zero operating time or power produces zero consumption.
What the estimate leaves out
The result is an appliance energy charge, not a reconstruction of the entire bill. Standing charges, taxes, demand charges, tiered pricing, time-of-use periods, export credits, and minimum bills are not included. If different rates apply at different times, calculate each period separately and add the costs rather than using an arbitrary cheap rate for all hours.
Worked example
A portable heater
Suppose a 1,500-watt heater runs at full power for four hours each day over 30 days. At a rate of 0.20 per kWh, daily energy is 1,500 / 1,000 × 4 = 6 kWh. Period energy is 6 × 30 = 180 kWh.
The results are Period cost $36.00, Period energy 180 kWh, Daily cost $1.20, and Daily energy 6 kWh. These figures assume four equivalent full-power hours, not four hours merely plugged in while a thermostat repeatedly switches the element off.
A small lighting load
For a 10-watt lamp used five hours per day over 30 days at 0.25 per kWh, daily energy is 0.05 kWh and period energy is 1.5 kWh. The unrounded period cost is 0.375 currency units, displayed as $0.38. Daily cost is 0.0125, displayed as $0.01. The period figure is calculated from unrounded energy and rate, not by multiplying the rounded daily display by 30.
Expert tips
Common mistakes
- Confusing watts with kilowatt-hours. Entering a monthly kWh figure into the power field multiplies energy by time again. This form begins with power; measured period energy needs only multiplication by the applicable rate.
- Using nameplate maximum power as a guaranteed average. Some equipment draws its rated maximum only briefly. Check whether the listed figure is input power, output capacity, or a maximum rating before treating it as continuous electrical consumption.
- Multiplying rounded daily cents to get the period bill. Small daily costs lose detail when displayed to two decimals. Trust the period calculation for the entered duration because it preserves precision until the final formatting step.
Frequently asked questions
Does this include my electricity standing charge?
No. It estimates only the variable energy charge for the entered appliance load. Add any relevant fixed charges, taxes, or other bill items separately.
Can I use a rate in pounds or euros?
Yes, provided all rate values use that currency consistently. The displayed dollar sign does not change the calculation and should be interpreted as your chosen currency unit.
How should I model standby power?
Calculate standby watts over the hours spent in standby separately, then add that cost to active-use cost. Avoid counting the same hours in both states.
Can I estimate several identical devices?
Yes. Multiply one device’s wattage by the number operating for the same hours, then enter that combined power. Devices with different schedules are clearer as separate calculations.
Does the calculator support solar export or negative prices?
No. The entered tariff must be nonnegative, and the model represents consumption at one rate. Export payments and variable market prices need a separate accounting model.
Related calculators
Related guides
MathPercentages people get wrong: change, difference and pointsThe denominator determines the answer. Learn to distinguish percentage change, symmetric difference and percentage-point movements.14 November 2026 · 7 min read
MathStandard deviation without the jargonThe average tells you the centre. Standard deviation helps describe the spread, provided you know what the data represents.14 November 2026 · 7 min readSources and standards
About the author
Dr. Hassan Khames Eliwa holds a PhD in Construction & Built Environment and has more than 20 years of international project controls experience. He is Director of Eliwa Project Controls Limited in Auckland and founder of PMMilestone.org and PMMilestone.com.
Buy me a coffee